My first mod on my 11 yrs old Babe...

[azam318]

After placed the console and the armrest were seated properly,
here is the final stage to be done.

Step 14: Tighten the 2 screws which located inside the back compartment.

Step 15: Place the compartment into the place. Ensure that, all the six
slots to fit in tightly.

Here is the armrest and the console look a like.

 

[azam318]

So, here is the end result after done so much things and had spent
a lots of time with deep in patient. The End... thanks for viewing. :wink:

Thanks:
azam318

 

[SpeedaddicT]

Waaaa.....manyak cunnn wooo...bravo & congrates bro Azam...:top::top:

Tgh gatal nak install jgk ni...huhuhu

 

[azam318]

Waaaa.....manyak cunnn wooo...bravo & congrates bro Azam...:top::top:
Tgh gatal nak install jgk ni...huhuhu

Heheheh .... apa lagi tunggu Bro SpeedaddicT, install jangan tak install... :rock:

 

[megatniza]

nice , bro . looks like factory fitted . so , now you are officially licensed to drink & drive ... he he he

 

[azam318]

nice , bro . looks like factory fitted . so , now you are officially licensed to drink & drive ... he he he

kekekekek...so funny lar, thanks bro megat...

 

[azam318]

So, below is my next DIY project... cup holder with LED build in... heheheh... :wink:
Will update, once its done... wish me good luck... :top:

Got this DIY pics from the outside bmw forums, hopefully i'll make
it too... soon...

 

[Russie]

wow cool DIY bro

 

[ejat shafiq]

LED in the cup holder! nice one man :top:

 

[azam318]

wow cool DIY bro

Thanks, Bro Russie...

 

[azam318]

LED in the cup holder! nice one man :top:

Bro ejat, thanks. I just want to make it as a hobby... heheheh... :smokin:

 

[ICEMAN 68]

wow wee ...darm nice ..... how to do ?? i want to install below my gas pedal can ahhh ???

 

[mizhan]

genius la lu bro!

 

[azam318]

wow wee ...darm nice ..... how to do ?? i want to install below my gas pedal can ahhh ???

Bro iceman, i think its also can be done. But need some modification for the mounting
on the LED if you tends to place it at gas pedal. For the wiring its not that difficult,
just to have the new wiring which is hook up to the 12v power supply either from
existing cigar inlet or console bulb. But remember to put the resistor 1k ohm in series
to the LED at positive path or you might need to do calculation on the resistor to be
use based on the LEd color. Because different LED color giving the different ampere
and voltage usage. Ignoring resitor will cause frequent LED blown.
That's all... good luck... :wink:

Thanks;
azam318

 

[azam318]

genius la lu bro!

Bro mizan, i'm not genius lar... i'm just doing syiok syiok only... heheheh... :wink:

 

[climenta]

Cool mod bro, just make sure the LEDs are properly sealed... you don't want moisture from your paper cups seeping in

 

[kayz]

Cun lah bro, macam ori fitted........................when you want to light up the drink console

 

[azam318]

Cool mod bro, just make sure the LEDs are properly sealed... you don't want moisture from your paper cups seeping in

Bro climenta, thanks for the advice... :top:

 

[azam318]

Cun lah bro, macam ori fitted........................when you want to light up the drink console

Thanks, Bro kayz. It will be soon and need some free time to fix it...

 

[infinityKL]

nice work there zam...