Stripping my other baby bare metal

[rezzy3181]

:rofl: From now on I will post as and when my work progress according to my mood and time, I have laid off my project for sometime and now the mood comes to finish my job and make my topless lady on the road back. (Moderator is it ok for me to post my other makes here?)No.1Had strip 3/4 of the car for some time but well covered with a grinding wire brush and here it goes.

 

[rezzy3181]

No.2
messy garage where I park my 2 old ladies, after stripping, there we can see all the covered rust being cemented so sad. :cry: hey my son do strip his bike and leave it for I think now more then a year fedup so lazy and now he uses my Austin which for once I don't allow him to touch, what to do boys are just boys.

 

[rezzy3181]

No.3

I enjoyed doing things myself so as can really clean to bare metal and it is so simple with the grinding brush but to be careful of flying wires can hurt you.... use glasses to protect you eyes.

 

[rezzy3181]

No.4

See the seals so badly done I think 1/2" think of cement, anyway I am going to do up to undercoating level then sent it to the welder for metalwork at lease I see all the work done properly to my satisfaction.

 

[rezzy3181]

No.5

Undercoat starts at back fender 1st coating, I did 3 coating.

 

[rezzy3181]

No.6

There are lots of body section to be smoothern as it was cemented over to cover before even little holes or rust.

 

[rezzy3181]

No.7

Taken from my house door

 

[rezzy3181]

No.8

Primered one side already not even 2 hrs

 

[rezzy3181]

No.9

 

[rezzy3181]

No.10

 

[rezzy3181]

No.11

My rear bonnet bad rust at both ends, let the welder make good after I complete my whole car in out and under

 

[rezzy3181]

No.12

see the rust at the edge and lips but I wirebrush till you can comb you hair shining.

 

[rezzy3181]

No.13

Its only 1st coat primmer

 

[rezzy3181]

No.14

This is my rear arch I strip the harden rubberize not finish yet, will clean and primer then if any rust will do it then spray the coating again myself.

 

[rezzy3181]

No.15

still rear arch, see the edge rust marks sick of it, if I own the car from new I don't think you can see rust as I clean my undercarrage and mudguard in every clean. the original colour was british racing green and it was red then now I will go back to the original colour. k:

 

[rezzy3181]

No.16

Lots of work to be done sad alone, got an adult only son lazy.
Thats all for today till I continue will post more pictures. :yes!:

 

[et5]

Wah Mr Rezzy
what are you using to kill off all the rust on your triumph? have u sorted out the engine yet?[hopefully not seized?]

nice work ..carry on!

 

[kevster30]

Rezzy,

Awesome stuff, thanks for sharing.... a word of advise, make sure you are using oxide primer when stripping to bare metal. This will prevent rust from forming.

Have fun and do post up the final results ya?

Cheers!

 

[ICEMAN 68]

Originally posted by rezzy3181@Sep 4 2005, 06:41 PM
No.16

Lots of work to be done sad alone, got an adult only son lazy.

no need to worry ... just call lerrr .... 2 to 10 bottle of beer or todi satu baldi will do

sure siap punya

nice car Tuan easy to pick up chicks

 

[et5]

Originally posted by kevster30@Sep 5 2005, 11:12 AM
Rezzy,

Awesome stuff, thanks for sharing.... a word of advise, make sure you are using oxide primer when stripping to bare metal. This will prevent rust from forming.

Have fun and do post up the final results ya?

Cheers!

TQ for tip sifu Kev~!

any particular brand of oxide primer?